Keep the frame square
Accurate diagonal measurements and rigid corner connections matter before the infill and hardware are finalized.
Aluglobus fence
ALU 60 T&G Black 6x6 ft. Heavy-Duty Pedestrian Gate Kit - Single Swing - NO GAP
ALU 60 T&G Black 6x6 ft. Heavy-Duty Pedestrian Gate Kit - Single Swing - NO GAP
Regular price
$1,646.06 USD
Regular price
Sale price
$1,646.06 USD
Unit price
per
Couldn't load pickup availability
Shipping & Returns
Shipping & Returns
Care Instructions
Care Instructions
Description
A single-swing, no-gap aluminum privacy gate built around a 4-inch heavy-duty frame, ALU60 tongue-and-groove infill, 6063-T6 aluminum, and heavy-duty hinge support. This is the Heavy-Duty Contractor Line version of the ALU60 T&G pedestrian gate, not the Universal DIY frame. At 6 feet wide by 6 feet high, this is a broad single-swing pedestrian gate, so hinge-side support and frame squareness matter even more than they do on a narrower leaf. The no-gap tongue-and-groove infill creates a solid privacy surface, while final performance depends on a rigid support condition, correct clearances and proper hardware alignment. The wall, post or structural support receiving the hinges must be appropriate for the gate and the actual mounting condition. Confirm finished ground clearance, swing path, latch-side clearance and stopper position before final tightening. Heavy-Duty framing and hardware are assembled around the actual opening and support condition. Interlocking tongue-and-groove aluminum creates a clean, continuous black gate face without intentional slat spacing. 6063-T6 aluminum and AAMA 2604 powder coating are used for durable exterior performance and low maintenance. The frame carries the gate as a framed assembly and provides the structure for the T&G infill, hinges and latch-side geometry. Interlocking tongue-and-groove boards form the privacy surface without the open spacing used by slat gate systems. Hinge alignment and the support behind it are critical to smooth swing, consistent clearances and long-term adjustment. Available post families include 2″, 2.75″ and 2″×3″ options. The correct support depends on the actual site and mounting plan. The gate package lists the following component families for the ALU60 T&G 6×6 Heavy-Duty gate. Exact cut lengths, quantities and site-specific support parts should be checked against the shipment and installation plan before fabrication begins. The gate is built around a dedicated frame so hinges, infill and latch-side geometry work as one assembly. ALU60 tongue-and-groove infill creates a solid visual barrier without the deliberate gaps used in slat systems. Aluminum avoids the rust behavior of ferrous steel and does not require the staining or sealing associated with real wood. AAMA 2604 architectural powder coating supports long-term exterior color and finish performance when properly maintained. A defined frame, T&G infill and hardware system helps crews build around repeatable components while still adapting to the actual opening. Use the video as a system reference, then confirm the exact 6×6 opening, hinge side, support condition and hardware plan for this ALU60 T&G Heavy-Duty gate before installation. Use the 6×6 single-swing format where a wider pedestrian opening is required and the hinge-side structure is designed to carry the larger leaf. The no-gap ALU60 T&G face helps create a clean, private entry rather than an open slat appearance. Coordinate the gate with ALU60 T&G fence or related Aluglobus aluminum systems where a consistent architectural language is required. Suitable for projects that need durable aluminum construction, a modern black finish and a wider pedestrian access opening. The gate system uses 6063-T6 aluminum with an architectural powder-coated exterior finish. The black finish creates a clean contemporary appearance while aluminum provides corrosion resistance and low routine maintenance. Aluminum is a non-combustible metal substrate. For defensible-space or Zone 0 projects, compliance must be evaluated for the complete installed assembly, nearby materials, clearances and local requirements. Final acceptance belongs to the applicable authority having jurisdiction. The listed size identifies the gate kit format. Final field layout still depends on hinge clearances, latch-side clearances, finished grade, support condition and the chosen hardware. Record clear width, finished height and ground conditions at the actual gate location. Confirm which side receives the hinges and whether the support is a wall, post or other approved structure. Lay out the Heavy-Duty frame, connect corners and compare diagonals before locking the assembly. Fit the black ALU60 tongue-and-groove boards and top-rail components according to the gate layout. Install the heavy-duty hinges, set the gate plumb and confirm smooth movement through the entire swing path. Finalize latch, lock, stopper and clearances only after the gate hangs correctly and operates without binding. Use the direct product checkout only when the size, hinge side, support condition and installation plan are already confirmed. Otherwise send the opening information first. Use the actual packaged parts, project drawings and site conditions as the controlling installation information for the ALU60 T&G Heavy-Duty gate. Inventory the ALU60 T&G infill, Heavy-Duty frame stock, corner hardware, hinges, stopper, top rail and fasteners before cutting. Lay out the 4″ Heavy-Duty frame components on a flat surface and confirm final cut dimensions from the opening plan. Connect the frame using the specified internal corner hardware, then verify squareness using diagonal measurements. Install the black ALU60 tongue-and-groove infill in sequence so the joints fully engage and the privacy face remains consistent. Mount the 5″ Heavy-Duty hinges to the gate and approved hinge-side support while maintaining the required operating clearances. Set the stopper, latch and lock hardware, then check plumb, level, swing, closing alignment and all fasteners. For the cleanest installation, gather the site information that controls the gate before material is cut, drilled or mounted.ALU 60 T&G Black 6×6 Heavy-Duty Pedestrian Gate Kit
Full-Frame Strength
Contractor-Line Gate Architecture
Exterior Powder-Coat Finish
Reinforced Hinge Support
6063-T6 Aluminum Construction
Field Assembly & Alignment
The frame, infill, hinge and support condition work as one gate system.
Build around the hinge side
Plan operating clearance
Built around a real gate frame, not loose infill with hinges.
Field-assembled Contractor Line
No-gap ALU60 T&G privacy
Architectural aluminum system
What makes the 6×6 ALU60 T&G gate a Contractor Line system.
4″ Heavy-Duty gate frame
ALU60 T&G black aluminum
5″ heavy-duty 2-way support hinge
Project-specific post or wall condition
Core components listed for this Contractor Line gate.
Heavy-Duty framing, full privacy and a low-maintenance aluminum exterior.
Framed gate construction
No-gap privacy
Low maintenance
Exterior powder coating
Contractor repeatability
See how Aluglobus approaches aluminum gate construction.
A black 6×6 aluminum privacy gate for wider pedestrian openings that need a framed, solid architectural look.
Side-yard access
Private pedestrian entries
Contractor fence projects
Residential and light commercial
Architectural aluminum instead of wood or ferrous steel.
6063-T6 aluminum + AAMA 2604
Non-combustible metal substrate
Build the 6×6 gate around the finished opening, not around a guessed square.
Measure the finished opening
Choose hinge side
Assemble square
Install T&G infill
Hang and align
Set closure hardware
Ready to order the black single-swing gate?
ALU60 Contractor Line assembly sequence.
Preparation
Frame layout
Frame assembly
T&G installation
Hinge installation
Final adjustment
ALU60 T&G Black 6×6 Heavy-Duty gate questions.
What makes this gate different from the Universal DIY ALU60 gate?
This product is the Heavy-Duty Contractor Line version. It uses Heavy-Duty gate framing and project-specific mounting/support planning rather than the Universal DIY wall-to-wall frame approach.Is the ALU60 T&G gate a no-gap privacy gate?
Yes. The ALU60 tongue-and-groove infill interlocks to create a continuous privacy face without the intentional spacing used in open slat gate systems.What material is the gate made from?
The gate system uses 6063-T6 architectural aluminum with black ALU60 T&G infill and an AAMA 2604 architectural powder-coated finish.Can the 6×6 Heavy-Duty gate be automated?
Automation should be reviewed separately. A Heavy-Duty frame does not by itself confirm motor compatibility. Hinge geometry, support structure, operator selection, safety devices, electrical work and local requirements all need to be evaluated.Which post size should I use?
Available post families include 2″, 2.75″ and 2″×3″ aluminum options. The correct support depends on the mounting condition, gate layout and project requirements, so confirm the support before ordering or drilling.What tools are typically needed for field assembly?
Typical gate assembly requires accurate measuring tools, a level, square, drill/driver, appropriate bits, wrenches and cutting equipment suitable for aluminum where field cutting is required. Follow the actual parts and installation plan for the project.Does the black aluminum gate require painting or staining?
No routine staining is required. The aluminum uses an architectural powder-coated finish. Clean with methods appropriate for powder-coated aluminum and avoid abrasive or chemically aggressive cleaners.Can Aluglobus help confirm the gate before I order?
Yes. Send the finished opening dimensions, photos, hinge-side support condition, swing direction, latch or lock requirement and project location so the configuration can be reviewed before purchase.Confirm the opening and hinge-side support before cutting a 6×6 Heavy-Duty gate frame.